Mitchell® Machines - #1 On Tour Worldwide - 26 Years
The Steelclub® Signature Angle Machine is the latest evolution of the world’s best bending machine and is our best seller. It uses Dual Precision Gauges for measuring and bending loft/lie angles on all irons and face/lie angles hybrids and metal woods. It doubles as a specification gauge that accurately measures loft, lie and face angles simultaneously with its patented measuring gauges.
100% Accurate Measurements | Mitchell Machines have precise measuring gauge assemblies unlike competitors' machines that use travel rods that flex and become loose creating inaccurate and inconsistent readings.
- Measures & Bends Iron - Loft & Lie Angles
- Measures & Bends Hybrid & Metal Wood - Face & Lie Angles
- True Face Angle Readings
- Patented Precision Slide-Bearing Gauges
- ¼-Degree Increments
- Precision Machined Steel
- CNC Milled
- Black Diamond Powder-Coat Base
- Measures & Bends In Same Fixture
- Eliminates Operator Error
- Easily Bends 17-4 & 431 Stainless Steel
- Adjust A Set Of Irons In 10 Mins Or Less
- Dual Precision Gauges For Easy Conversion To Left-Hand
- Patented Clamping Fixtures
- Secure Clamping For Precise Bending
- Non-Marring Clamps
- Clamps All Iron Heads Quickly
- Clamps Wide Top Line Irons
- Clamps Any Sole Radius
- Clamps Square-Triangular-Round Driver Head Shapes
- Clamps Hybrid Clubs
- Completely Assembled
Included With Machine:
- Angle Charts
- 27’ Roll Face Fixture Tape
- Instruction Manual
- Iron Clamps
- Metal Wood Clamps
- Hybrid Clamps
- 27” Standard Hosel Adjustable Bending Bar
- 27” Short Hosel Adjustable Bending Bar
- Heavy Duty 40” Floor Mount Stand (Installation Hardware Included)
Loft & Lie Angles - Irons
The Steelclub® Signature Angle Machine is a precision gauge for measuring and bending loft/lie angles on all irons. A complete set of irons can be measured and adjusted in less then 10 minutes. It clamps all iron sole radiuses and wide top line designs. It easily bends 17-4 and 431 cast stainless steel and forged carbon steel heads. Technicians measure and bend in the same fixture, which eliminates operator error caused from using other measuring devices.
Face & Lie Angles - Hybrids & Metal Woods
Steelclub® Signature Angle Machine is a true face angle measuring gauge. Golf club specification gauges do not properly measure face angles. They do not register the club head in a square, centered, horizontal face attitude. They clamp the shaft and allow the head to seek a face angle position influenced by the sole radius. A true face angle measurement is the angle of the face plane compared to the shaft plane. Only Steelclub® Technology properly registers the club head and measures the shaft plane in relation to the square face plane.
Steelclub® Signature Angle Machine has a universal Top Clamp that works for hybrids and metal woods by flipping the Wood Pad down. Back Clamps fit all sizes and shapes of heads. Unique Sole Fixtures adjust to center club head in the face fixture. A progressive scale for marking center of head is located on front of machine. The sole clamps securely hold hybrids and metal woods without damage. Stainless steel hybrid and metal woods clubs that have polished hosels long enough to accept the Steelclub® Adjustable Short Hosel Bending Bar can be adjusted.
It is recommended to adjust hybrid face angles to a square position to ensure the playing loft is equal to the loft on the sole of the head. Lie angles should be fit to each golfer just like iron clubs.
It is recommended to adjust face angles for drivers and fairway metals in a range from square to 2 degrees open or closed to change ball flight. Metal woods should have similar face angles within the set for consistency. Adjust lie angles to fit golfers just like iron clubs. Some titanium drivers with long hosels can be adjusted.
Use As Spec Gauge For Adjustable Tip Clubs
The new self-adjusting drivers, fairway metals and hybrids can be checked to record the actual adjustments made by repositioning the adapter.